18 · Saws

Tile Saw

Also called Wet tile saw · Tile cutter · Bridge tile saw

A water-cooled diamond saw for precise, chip-free cuts in ceramic, porcelain, stone and glass tile.

Electric (corded)

Sizes & models we rent

8"–12" wet sawStands available in mini and regular

Overview

A tile saw runs a diamond blade through a water bath, so the blade stays cool and the dust leaves as slurry rather than air. That is what gives a chip-free edge in a brittle material.

We rent an 8 in, with mini and regular stands available.

Porcelain and ceramic floor tile, stone, marble and granite, backsplash and mosaic, and angled or notched cuts.

Fill the water tray to the line before switching on. Feed the tile slowly, and slow right down in the last inch — most chipping happens as the blade exits the far edge.

Catalogue specifications

TP1020 CUTS UP TO 20" TILES
TP1024 CUTS UP TO 24" TILES
CAN CUT 45 AND 60 DEGREE ANGLES - WITH THE USE OF ATTACHMENTS AT NO ADDITIONAL COST

Best uses

Porcelain and ceramic floor tile
Stone, marble and granite tile
Backsplash and mosaic tile
Angled and notched cuts

Troubleshooting

Find a symptom

Tile chipping along the cut

Checks to try, in order

Feed more slowly.
Top up the water.
Porcelain needs a continuous-rim diamond blade — ask for one if it's chipping.

Reference draft — always follow the manufacturer’s manual.

Link to this fixDid this solve the problem?

Water spraying everywhere

Checks to try, in order

Fit the splash guards.
Turn down the water flow.

Reference draft — always follow the manufacturer’s manual.

Link to this fixDid this solve the problem?

Blade isn't cutting

Checks to try, in order

The diamonds may be glazed — dress the blade on a dressing stone or soft brick.

Reference draft — always follow the manufacturer’s manual.

Link to this fixDid this solve the problem?

Tool won't switch onShared · Electric (corded)

Likely causes

Tripped GFCI or breaker
Lock-off button
Damaged cord
Dead outlet

Checks to try, in order

Check the outlet works and reset any GFCI / RCD that has tripped.
Release the lock-off button or safety switch before squeezing the trigger.
Inspect the cord and extension lead for cuts, crushed sections or damaged plugs.
If running from a generator, make sure it's running and its breaker hasn't tripped.

A damaged cord or plug means the tool is out of service. Tag it and return it — never tape a cord.

Reference draft — always follow the manufacturer’s manual.

Link to this fixDid this solve the problem?

Keeps tripping the breakerShared · Electric (corded)

Likely causes

Circuit overloaded
Undersized extension cord
Blunt accessory

Checks to try, in order

Plug into a circuit with nothing else heavy running on it.
Use a shorter, heavier extension cord. Long, thin cords starve the motor and trip breakers.
Don't force the tool — a dull bit, blade or disc makes the motor draw more current.

Reference draft — always follow the manufacturer’s manual.

Link to this fixDid this solve the problem?

Overheating, burning smell or heavy sparkingShared · Electric (corded)

Checks to try, in order

Stop and unplug the tool.
Check the motor vents aren't blocked with dust.
Let it cool, fit a sharp accessory and let the tool's weight do the work.

Heavy sparking from the vents or a burning smell that returns points to worn brushes or a failing motor — workshop only.

Reference draft — always follow the manufacturer’s manual.

Link to this fixDid this solve the problem?

Safety

Always plug into a GFCI — this saw mixes water and electricity.
Keep fingers clear of the blade; use a push stick for small pieces.

For electric (corded)

Inspect the cord and plug before every use. Use a GFCI/RCD outdoors or near water.
Unplug before changing blades, bits, discs or pads.
Wear eye protection, and a dust mask when cutting, grinding or sanding masonry.