15 · Power Tools

Power Planer

Also called Electric planer · Hand planer

A handheld planer that shaves thin layers off wood to flatten boards, trim doors and chamfer edges.

Electric (corded)

Sizes & models we rent

Show all models
Standard4-3/8" largeWider cut per pass

Selected model

Power Planer · Standard

View the Standard in the catalogue ↗Compare →

Overview

A power planer runs a spinning cutter block between two flat shoes, shaving a thin, even layer off a wooden surface with every pass.

We rent a standard planer and a 4-3/8 in that takes a wider cut per pass.

Trimming a sticking door, flattening joists and beams, chamfering edges, and scribing boards to fit an uneven wall.

Set a shallow depth and take several passes rather than one deep cut. Start each pass with the pressure on the front shoe and finish with it on the rear shoe — that is what stops the planer dipping at the beginning and the end of a board.

Best uses

  • Trimming sticking doors
  • Flattening joists and beams
  • Chamfering edges
  • Scribing boards to fit

Troubleshooting

Rough finish or tear-out

Checks to try, in order

  1. Slow down your feed rate.
  2. Plane with the grain.
  3. Blunt blades cause tear-out — swap or turn them.

Reference draft — always follow the manufacturer’s manual.

Link to this fixDid this solve the problem?
Dips at the start or end of the board

Checks to try, in order

  1. Shift your pressure from the front shoe to the rear shoe as you move through the pass.

Reference draft — always follow the manufacturer’s manual.

Link to this fixDid this solve the problem?
Tool won't switch onShared · Electric (corded)

Likely causes

  • Tripped GFCI or breaker
  • Lock-off button
  • Damaged cord
  • Dead outlet

Checks to try, in order

  1. Check the outlet works and reset any GFCI / RCD that has tripped.
  2. Release the lock-off button or safety switch before squeezing the trigger.
  3. Inspect the cord and extension lead for cuts, crushed sections or damaged plugs.
  4. If running from a generator, make sure it's running and its breaker hasn't tripped.

A damaged cord or plug means the tool is out of service. Tag it and return it — never tape a cord.

Reference draft — always follow the manufacturer’s manual.

Link to this fixDid this solve the problem?
Keeps tripping the breakerShared · Electric (corded)

Likely causes

  • Circuit overloaded
  • Undersized extension cord
  • Blunt accessory

Checks to try, in order

  1. Plug into a circuit with nothing else heavy running on it.
  2. Use a shorter, heavier extension cord. Long, thin cords starve the motor and trip breakers.
  3. Don't force the tool — a dull bit, blade or disc makes the motor draw more current.

Reference draft — always follow the manufacturer’s manual.

Link to this fixDid this solve the problem?
Overheating, burning smell or heavy sparkingShared · Electric (corded)

Checks to try, in order

  1. Stop and unplug the tool.
  2. Check the motor vents aren't blocked with dust.
  3. Let it cool, fit a sharp accessory and let the tool's weight do the work.

Heavy sparking from the vents or a burning smell that returns points to worn brushes or a failing motor — workshop only.

Reference draft — always follow the manufacturer’s manual.

Link to this fixDid this solve the problem?

Safety

For electric (corded)

  • Inspect the cord and plug before every use. Use a GFCI/RCD outdoors or near water.
  • Unplug before changing blades, bits, discs or pads.
  • Wear eye protection, and a dust mask when cutting, grinding or sanding masonry.

Videos & links

Related equipment

All Power Tools →

Always follow the manufacturer’s manual and site safety rules. Favourites and viewing history are stored on this device.